NVME-CREATE-NS(1) NVMe Manual NVME-CREATE-NS(1)
NAME
nvme-create-ns - Send NVMe Namespace management command to create
namespace, returns results.
SYNOPSIS
nvme create-ns <device> [--nsze=<nsze> | -s <nsze>]
[--ncap=<ncap> | -c <ncap>]
[--flbas=<flbas> | -f <flbas>]
[--dps=<dps> | -d <dps>]
[--nmic=<nmic> | -m <nmic>]
[--anagrp-id=<anagrpid> | -a <anagrpid>]
[--nvmset-id=<nvmsetid> | -i <nvmsetid>]
[--endg-id=<endgid> | -e <endgid>]
[--csi=<command_set_identifier> | -y <command_set_identifier>]
[--lbstm=<lbstm> | -l <lbstm>]
[--nphndls=<nphndls> | -n <nphndls>]
[--block-size=<block-size> | -b <block-size>]
[--timeout=<timeout> | -t <timeout>]
[--nsze-si=<nsze-si> | -S <nsze-si>]
[--ncap-si=<ncap-si> | -C <ncap-si>]
[--azr | -z]
[--rar=<rar> | -r <rar>]
[--ror=<ror> | -O <ror>]
[--rnumzrwa=<rnumzrwa> | -u <rnumzrwa>]
[--phndls=<placement-handle-list,> | -p <placement-handle-list,>]
[--output-format=<fmt> | -o <fmt>] [--verbose | -v]
DESCRIPTION
For the NVMe device given, sends a namespace management command to
create the namespace with the requested settings. On success, the
namespace identifier assigned by the controller is returned.
The <device> parameter is mandatory and may be either the NVMe character
device (ex: /dev/nvme0), or a namespace block device (ex: /dev/nvme0n1).
OPTIONS
-s, --nsze
The namespace size.
-c, --ncap
The namespace capacity.
-f, --flbas
The namespace formatted logical block size setting. Conflicts with
--block-size argument.
-d, --dps
The data protection settings.
-m, --nmic
Namespace multipath and sharing capabilities.
-a, --anagrp-id
ANA Group Identifier. If this value is 0h specifies that the
controller determines the value to use
-i <nvmsetid>, --nvmset-id=<nvmsetid>
This field specifies the identifier of the NVM Set.
-e <endgid>, --endg-id=<endgid>
This field specifies the identifier of the endurance group.
-y <command_set_identifier>, --csi=<command_set_identifier>
This field specifies the identifier of command set. if not issued,
NVM Command Set will be selected.
-l <lbstm>, --lbstm=<lbstm>
Logical Block Storage Tag Mask for end-to-end protection.
-n <nphndls>, --nphndls=<nphndls>
Number of Placement Handle included in the Placement Handle List. If
the Flexible Data Placement capability is not supported or not
enabled in specified Endurance Group, then the controller shall
ignore this field.
-b, --block-size
Target block size the new namespace should be formatted as.
Potential FLBAS values will be values will be scanned and the lowest
numbered will be selected for the create-ns operation. Conflicts
with --flbas argument.
-S, --nsze-si
The namespace size (NSZE) in standard SI units (aligned on 1Mib
boundaries, unless the controller recommends a different value, see
namespace granularity). The value SI suffixed is divided by the
namespace LBA size to set as NSZE. If the value not suffixed it is
set as same with the nsze option.
-C, --ncap-si
The namespace capacity (NCAP) in standard SI units (aligned on 1Mib
boundaries, unless the controller recommends a different value, see
namespace granularity). The value SI suffixed is divided by the
namespace LBA size to set as NCAP. If the value not suffixed it is
set as same with the ncap option.
-z, --azr
Allocate ZRWA Resources. If set to 1, then the namespace is to be
created with the number of ZRWA resource specified in the RNUMZRWA
field of this data structure. If cleared to 0, then no ZRWA
resources are allocated to the namespace to be created.
-r <rar>, --rar=<rar>
Requested Active Resources. This field specifies the number of
active resources to be allocated to the created namespace.
-O <ror>, --ror=<ror>
Requested Open Resources. This field specifies the number of open
resources to be allocated to the created namespace.
-u <rnumzrwa>, --rnumzrwa=<rnumzrwa>
Requested Number of ZRWA Resources. This field specifies the number
of ZRWA resources to be allocated to the created namespace.
-p <placement-handle-list,>, --phndls=<placement-handle-list,>
The comma separated list of Reclaim Unit Handle Identifier to be
associated with each Placement Handle.
-o <fmt>, --output-format=<fmt>
Set the reporting format to normal, json or binary. Only one output
format can be used at a time.
-v, --verbose
Increase the information detail in the output.
-t <timeout>, --timeout=<timeout>
Override default timeout value 120,000. In milliseconds.
EXAMPLES
• Create a namespace:
# nvme create-ns /dev/nvme0 --nsze 11995709440 --ncap 1199570940 --flbas 0 --dps 0 --nmic 0
# nvme create-ns /dev/nvme0 --nsze-si 6.14T --ncap 1199570940 --flbas 0 --dps 0 --nmic 0
NVME
Part of the nvme-user suite
NVMe 05/02/2025 NVME-CREATE-NS(1)
Generated by dwww version 1.16 on Mon Nov 9 19:11:47 CET 2026.