YAML configuration(5) YAML configuration(5)
NAME
netplan - YAML network configuration abstraction for various backends
SYNOPSIS
netplan [ COMMAND | help ]
COMMANDS
See netplan help for a list of available commands on this system.
DESCRIPTION
Introduction
Distribution installers, cloud instantiation, image builds for particu-
lar devices, or any other way to deploy an operating system put its de-
sired network configuration into YAML configuration file(s). During
early boot, the netplan "network renderer" runs which reads
/{lib,etc,run}/netplan/*.yaml and writes configuration to /run to hand
off control of devices to the specified networking daemon.
• Configured devices get handled by systemd-networkd by default, unless
explicitly marked as managed by a specific renderer (NetworkManager)
• Devices not covered by the network config do not get touched at all.
• Usable in initramfs (few dependencies and fast)
• No persistent generated config, only original YAML config
• Parser supports multiple config files to allow applications like lib-
virt or lxd to package up expected network config (virbr0, lxdbr0),
or to change the global default policy to use NetworkManager for ev-
erything.
• Retains the flexibility to change backends/policy later or adjust to
removing NetworkManager, as generated configuration is ephemeral.
General structure
netplan's configuration files use the YAML
(http://yaml.org/spec/1.1/current.html) format. All
/{lib,etc,run}/netplan/*.yaml are considered. Lexicographically later
files (regardless of in which directory they are) amend (new mapping
keys) or override (same mapping keys) previous ones. A file in
/run/netplan completely shadows a file with same name in /etc/netplan,
and a file in either of those directories shadows a file with the same
name in /lib/netplan.
The top-level node in a netplan configuration file is a network: map-
ping that contains version: 2 (the YAML currently being used by curtin,
MaaS, etc. is version 1), and then device definitions grouped by their
type, such as ethernets:, modems:, wifis:, or bridges:. These are the
types that our renderer can understand and are supported by our back-
ends.
Each type block contains device definitions as a map where the keys
(called "configuration IDs") are defined as below.
Device configuration IDs
The key names below the per-device-type definition maps (like ether-
nets:) are called "ID"s. They must be unique throughout the entire set
of configuration files. Their primary purpose is to serve as anchor
names for composite devices, for example to enumerate the members of a
bridge that is currently being defined.
(Since 0.97) If an interface is defined with an ID in a configuration
file; it will be brought up by the applicable renderer. To not have
netplan touch an interface at all, it should be completely omitted from
the netplan configuration files.
There are two physically/structurally different classes of device defi-
nitions, and the ID field has a different interpretation for each:
Physical devices
(Examples: ethernet, modem, wifi) These can dynamically come and
go between reboots and even during runtime (hot plugging). In
the generic case, they can be selected by match: rules on de-
sired properties, such as name/name pattern, MAC address, driv-
er, or device paths. In general these will match any number of
devices (unless they refer to properties which are unique such
as the full path or MAC address), so without further knowledge
about the hardware these will always be considered as a group.
It is valid to specify no match rules at all, in which case the
ID field is simply the interface name to be matched. This is
mostly useful if you want to keep simple cases simple, and it's
how network device configuration has been done for a long time.
If there are match: rules, then the ID field is a purely opaque
name which is only being used for references from definitions of
compound devices in the config.
Virtual devices
(Examples: veth, bridge, bond, vrf) These are fully under the
control of the config file(s) and the network stack. I. e.
these devices are being created instead of matched. Thus match:
and set-name: are not applicable for these, and the ID field is
the name of the created virtual device.
Top-level configuration structure
The general structure of a Netplan YAML file is shown below.
network:
version: NUMBER
renderer: STRING
bonds: MAPPING
bridges: MAPPING
ethernets: MAPPING
modems: MAPPING
tunnels: MAPPING
vlans: MAPPING
vrfs: MAPPING
wifis: MAPPING
nm-devices: MAPPING
• version (number)
Defines what version of the configuration format is used. The
only value supported is 2. Defaults to 2 if not defined.
• renderer (scalar)
Defines what network configuration tool will be used to set up
your configuration. Valid values are networkd and NetworkMan-
ager. Defaults to networkd if not defined.
• bonds (mapping)
Creates and configures link aggregation (bonding) devices.
• bridges (mapping)
Creates and configures bridge devices.
• ethernets (mapping)
Configures physical Ethernet interfaces.
• modems (mapping)
Configures modems
• tunnels (mapping)
Creates and configures different types of virtual tunnels.
• vlans (mapping)
Creates and configures VLANs.
• vrfs (mapping)
Configures Virtual Routing and Forwarding (VRF) devices.
• wifis (mapping)
Configures physical Wifi interfaces as client, adhoc or access
point.
• nm-devices (mapping)
nm-devices are used in situations where Netplan doesn't sup-
port the connection type. The raw configuration expected by
NetworkManager can be defined and will be passed as is
(passthrough) to the .nmconnection file. Users will not nor-
mally use this type of device.
All the properties for all the device types will be described in the
next sections.
Properties for physical device types
These properties are used with physical devices such as Ethernet and
Wifi network interfaces.
Note: Some options will not work reliably for devices matched by name
only and rendered by networkd, due to interactions with device renaming
in udev. Match devices by MAC when setting options like: wakeonlan or
*-offload.
• match (mapping)
This selects a subset of available physical devices by various
hardware properties. The following configuration will then
apply to all matching devices, as soon as they appear. All
specified properties must match.
• name (scalar)
Current interface name. Globs are supported, and the prima-
ry use case for matching on names, as selecting one fixed
name can be more easily achieved with having no match: at
all and just using the ID (see above). (NetworkManager: as
of v1.14.0)
• macaddress (scalar)
Device's 6-byte permanent MAC address in the form
"XX:XX:XX:XX:XX:XX" or 20 bytes for InfiniBand devices
(IPoIB). Globs are not allowed. This doesn't match virtual
MAC addresses for veth, bridge, bond, vlan, ...
• driver (scalar or sequence of scalars) – sequence since 0.104
Kernel driver name, corresponding to the DRIVER udev proper-
ty. A sequence of globs is supported, any of which must
match. Matching on driver is only supported with networkd.
Examples:
• All cards on second PCI bus:
network:
ethernets:
myinterface:
match:
name: enp2*
• Fixed MAC address:
network:
ethernets:
interface0:
match:
macaddress: 11:22:33:AA:BB:FF
• First card of driver ixgbe:
network:
ethernets:
nic0:
match:
driver: ixgbe
name: en*s0
• First card with a driver matching bcmgenet or smsc*:
network:
ethernets:
nic0:
match:
driver: ["bcmgenet", "smsc*"]
name: en*
• set-name (scalar)
When matching on unique properties such as path or MAC, or
with additional assumptions such as "there will only ever be
one wifi device", match rules can be written so that they only
match one device. Then this property can be used to give that
device a more specific/desirable/nicer name than the default
from udev's ifnames. Any additional device that satisfies the
match rules will then fail to get renamed and keep the origi-
nal kernel name (and dmesg will show an error).
• wakeonlan (bool)
Enable wake on LAN. Off by default.
• emit-lldp (bool) – since 0.99
(networkd backend only) Whether to emit LLDP packets. Off by
default.
• receive-checksum-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the hardware
offload for checksumming of ingress network packets is enabled
(disabled). When unset, the kernel's default will be used.
• transmit-checksum-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the hardware
offload for checksumming of egress network packets is enabled
(disabled). When unset, the kernel's default will be used.
• tcp-segmentation-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the TCP Seg-
mentation Offload (TSO) is enabled (disabled). When unset,
the kernel's default will be used.
• tcp6-segmentation-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the TCP6 Seg-
mentation Offload (tx-tcp6-segmentation) is enabled (dis-
abled). When unset, the kernel's default will be used.
• generic-segmentation-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the Generic
Segmentation Offload (GSO) is enabled (disabled). When unset,
the kernel's default will be used.
• generic-receive-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the Generic
Receive Offload (GRO) is enabled (disabled). When unset, the
kernel's default will be used.
• large-receive-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the Large Re-
ceive Offload (LRO) is enabled (disabled). When unset, the
kernel's default will be used.
• openvswitch (mapping) – since 0.100
This provides additional configuration for the openvswitch
network device. If Open vSwitch is not available on the sys-
tem, netplan treats the presence of openvswitch configuration
as an error.
Any supported network device that is declared with the open-
vswitch mapping (or any bond/bridge that includes an interface
with an openvswitch configuration) will be created in open-
vswitch instead of the defined renderer. In the case of a
vlan definition declared the same way, netplan will create a
fake VLAN bridge in openvswitch with the requested vlan prop-
erties.
• external-ids (mapping) – since 0.100
Passed-through directly to Open vSwitch
• other-config (mapping) – since 0.100
Passed-through directly to Open vSwitch
• lacp (scalar) – since 0.100
Valid for bond interfaces. Accepts active, passive or off
(the default).
• fail-mode (scalar) – since 0.100
Valid for bridge interfaces. Accepts secure or standalone
(the default).
• mcast-snooping (bool) – since 0.100
Valid for bridge interfaces. False by default.
• protocols (sequence of scalars) – since 0.100
Valid for bridge interfaces or the network section. List of
protocols to be used when negotiating a connection with the
controller. Accepts OpenFlow10, OpenFlow11, OpenFlow12,
OpenFlow13, OpenFlow14, and OpenFlow15.
• rstp (bool) – since 0.100
Valid for bridge interfaces. False by default.
• controller (mapping) – since 0.100
Valid for bridge interfaces. Specify an external OpenFlow
controller.
• addresses (sequence of scalars)
Set the list of addresses to use for the controller tar-
gets. The syntax of these addresses is as defined in ovs-
vsctl(8). Example: addresses: [tcp:127.0.0.1:6653,
"ssl:[fe80::1234%eth0]:6653"]
• connection-mode (scalar)
Set the connection mode for the controller. Supported op-
tions are in-band and out-of-band. The default is in-
band.
• ports (sequence of sequence of scalars) – since 0.100
Open vSwitch patch ports. Each port is declared as a pair
of names which can be referenced as interfaces in dependent
virtual devices (bonds, bridges).
Example:
openvswitch:
ports:
- [patch0-1, patch1-0]
• ssl (mapping) – since 0.100
Valid for global openvswitch settings. Options for config-
uring SSL server endpoint for the switch.
• ca-cert (scalar)
Path to a file containing the CA certificate to be used.
• certificate (scalar)
Path to a file containing the server certificate.
• private-key (scalar)
Path to a file containing the private key for the server.
Properties for all device types
• renderer (scalar)
Use the given networking backend for this definition. Cur-
rently supported are networkd and NetworkManager. This prop-
erty can be specified globally in network:, for a device type
(in e. g. ethernets:) or for a particular device definition.
Default is networkd.
(Since 0.99) The renderer property has one additional accept-
able value for vlan objects (i. e. defined in vlans:): sri-
ov. If a vlan is defined with the sriov renderer for an SR-
IOV Virtual Function interface, this causes netplan to set up
a hardware VLAN filter for it. There can be only one defined
per VF.
• dhcp4 (bool)
Enable DHCP for IPv4. Off by default.
• dhcp6 (bool)
Enable DHCP for IPv6. Off by default. This covers both
stateless DHCP - where the DHCP server supplies information
like DNS nameservers but not the IP address - and stateful
DHCP, where the server provides both the address and the other
information.
If you are in an IPv6-only environment with completely state-
less auto-configuration (SLAAC with RDNSS), this option can be
set to cause the interface to be brought up. (Setting accept-
ra alone is not sufficient.) Auto-configuration will still
honor the contents of the router advertisement and only use
DHCP if requested in the RA.
Note that rdnssd(8) is required to use RDNSS with networkd.
No extra software is required for NetworkManager.
• ipv6-mtu (scalar) – since 0.98 > Set the IPv6 MTU (only supported
with networkd backend). Note > that needing to set this is an unusu-
al requirement. > > Requires feature: ipv6-mtu
• ipv6-privacy (bool)
Enable IPv6 Privacy Extensions (RFC 4941) for the specified
interface, and prefer temporary addresses. Defaults to false
- no privacy extensions. There is currently no way to have a
private address but prefer the public address.
• link-local (sequence of scalars)
Configure the link-local addresses to bring up. Valid options
are 'ipv4' and 'ipv6', which respectively allow enabling IPv4
and IPv6 link local addressing. If this field is not defined,
the default is to enable only IPv6 link-local addresses. If
the field is defined but configured as an empty set, IPv6
link-local addresses are disabled as well as IPv4 link- local
addresses.
This feature enables or disables link-local addresses for a
protocol, but the actual implementation differs per backend.
On networkd, this directly changes the behavior and may add an
extra address on an interface. When using the NetworkManager
backend, enabling link-local has no effect if the interface
also has DHCP enabled.
Examples:
• Enable only IPv4 link-local: link-local: [ ipv4 ]
• Enable all link-local addresses: link-local: [ ipv4, ipv6 ]
• Disable all link-local addresses: link-local: [ ]
• ignore-carrier (bool) – since 0.104
(networkd backend only) Allow the specified interface to be
configured even if it has no carrier.
• critical (bool)
Designate the connection as "critical to the system", meaning
that special care will be taken by to not release the assigned
IP when the daemon is restarted. (not recognized by Network-
Manager)
• dhcp-identifier (scalar)
(networkd backend only) Sets the source of DHCPv4 client iden-
tifier. If mac is specified, the MAC address of the link is
used. If this option is omitted, or if duid is specified,
networkd will generate an RFC4361-compliant client identifier
for the interface by combining the link's IAID and DUID.
• dhcp4-overrides (mapping)
(networkd backend only) Overrides default DHCP behavior; see
the DHCP Overrides section below.
• dhcp6-overrides (mapping)
(networkd backend only) Overrides default DHCP behavior; see
the DHCP Overrides section below.
• accept-ra (bool)
Accept Router Advertisement that would have the kernel config-
ure IPv6 by itself. When enabled, accept Router Advertise-
ments. When disabled, do not respond to Router Advertise-
ments. If unset use the host kernel default setting.
• addresses (sequence of scalars and mappings)
Add static addresses to the interface in addition to the ones
received through DHCP or RA. Each sequence entry is in CIDR
notation, i. e. of the form addr/prefixlen. addr is an IPv4
or IPv6 address as recognized by inet_pton(3) and prefixlen
the number of bits of the subnet.
For virtual devices (bridges, bonds, vlan) if there is no ad-
dress configured and DHCP is disabled, the interface may still
be brought online, but will not be addressable from the net-
work.
In addition to the addresses themselves one can specify con-
figuration parameters as mappings. Current supported options
are:
• lifetime (scalar) – since 0.100
Default: forever. This can be forever or 0 and corresponds
to the PreferredLifetime option in systemd-networkd's Ad-
dress section. Currently supported on the networkd backend
only.
• label (scalar) – since 0.100
An IP address label, equivalent to the ip address label com-
mand. Currently supported on the networkd backend only.
Examples:
• Simple: addresses: [192.168.14.2/24, "2001:1::1/64"]
• Advanced:
network:
ethernets:
eth0:
addresses:
- "10.0.0.15/24":
lifetime: 0
label: "maas"
- "2001:1::1/64"
• ipv6-address-generation (scalar) – since 0.99
Configure method for creating the address for use with RFC4862
IPv6 Stateless Address Auto-configuration (only supported with
NetworkManager backend). Possible values are eui64 or stable-
privacy.
• ipv6-address-token (scalar) – since 0.100
Define an IPv6 address token for creating a static interface
identifier for IPv6 Stateless Address Auto-configuration.
This is mutually exclusive with ipv6-address-generation.
• gateway4, gateway6 (scalar)
Deprecated, see Default routes. Set default gateway for
IPv4/6, for manual address configuration. This requires set-
ting addresses too. Gateway IPs must be in a form recognized
by inet_pton(3). There should only be a single gateway per IP
address family set in your global config, to make it unambigu-
ous. If you need multiple default routes, please define them
via routing-policy.
Examples
• IPv4: gateway4: 172.16.0.1
• IPv6: gateway6: "2001:4::1"
• nameservers (mapping)
Set DNS servers and search domains, for manual address config-
uration. There are two supported fields: addresses: is a list
of IPv4 or IPv6 addresses similar to gateway*, and search: is
a list of search domains.
Example:
network:
ethernets:
id0:
[...]
nameservers:
search: [lab, home]
addresses: [8.8.8.8, "FEDC::1"]
• macaddress (scalar)
Set the device's MAC address. The MAC address must be in the
form "XX:XX:XX:XX:XX:XX".
Note: This will not work reliably for devices matched by name
only and rendered by networkd, due to interactions with device
renaming in udev. Match devices by MAC when setting MAC ad-
dresses.
Example:
network:
ethernets:
id0:
match:
macaddress: 52:54:00:6b:3c:58
[...]
macaddress: 52:54:00:6b:3c:59
• mtu (scalar)
Set the Maximum Transmission Unit for the interface. The de-
fault is 1500. Valid values depend on your network interface.
Note: This will not work reliably for devices matched by name
only and rendered by networkd, due to interactions with device
renaming in udev. Match devices by MAC when setting MTU.
• optional (bool)
An optional device is not required for booting. Normally,
networkd will wait some time for device to become configured
before proceeding with booting. However, if a device is
marked as optional, networkd will not wait for it. This is
only supported by networkd, and the default is false.
Example:
network:
ethernets:
eth7:
# this is plugged into a test network that is often
# down - don't wait for it to come up during boot.
dhcp4: true
optional: true
• optional-addresses (sequence of scalars)
Specify types of addresses that are not required for a device
to be considered online. This changes the behavior of back-
ends at boot time to avoid waiting for addresses that are
marked optional, and thus consider the interface as "usable"
sooner. This does not disable these addresses, which will be
brought up anyway.
Example:
network:
ethernets:
eth7:
dhcp4: true
dhcp6: true
optional-addresses: [ ipv4-ll, dhcp6 ]
• activation-mode (scalar) – since 0.103
Allows specifying the management policy of the selected inter-
face. By default, netplan brings up any configured interface
if possible. Using the activation-mode setting users can
override that behavior by either specifying manual, to hand
over control over the interface state to the administrator or
(for networkd backend only) off to force the link in a down
state at all times. Any interface with activation-mode de-
fined is implicitly considered optional. Supported officially
as of networkd v248+.
Example:
network:
ethernets:
eth1:
# this interface will not be put into an UP state automatically
dhcp4: true
activation-mode: manual
• routes (sequence of mappings)
Configure static routing for the device; see the Routing sec-
tion below.
• routing-policy (sequence of mappings)
Configure policy routing for the device; see the Routing sec-
tion below.
• neigh-suppress (scalar) – since 0.105
Takes a boolean. Configures whether ARP and ND neighbor sup-
pression is enabled for this port. When unset, the kernel's
default will be used.
DHCP Overrides
Several DHCP behavior overrides are available. Most currently only
have any effect when using the networkd backend, with the exception of
use-routes and route-metric.
Overrides only have an effect if the corresponding dhcp4 or dhcp6 is
set to true.
If both dhcp4 and dhcp6 are true, the networkd backend requires that
dhcp4-overrides and dhcp6-overrides contain the same keys and values.
If the values do not match, an error will be shown and the network con-
figuration will not be applied.
When using the NetworkManager backend, different values may be speci-
fied for dhcp4-overrides and dhcp6-overrides, and will be applied to
the DHCP client processes as specified in the netplan YAML.
• dhcp4-overrides, dhcp6-overrides (mapping)
The dhcp4-overrides and `dhcp6-override`` mappings override
the default DHCP behavior.
• use-dns (bool)
Default: true. When true, the DNS servers received from the
DHCP server will be used and take precedence over any stati-
cally configured ones. Currently only has an effect on the
networkd backend.
• use-ntp (bool)
Default: true. When true, the NTP servers received from the
DHCP server will be used by systemd-timesyncd and take
precedence over any statically configured ones. Currently
only has an effect on the networkd backend.
• send-hostname (bool)
Default: true. When true, the machine's hostname will be
sent to the DHCP server. Currently only has an effect on
the networkd backend.
• use-hostname (bool)
Default: true. When true, the hostname received from the
DHCP server will be set as the transient hostname of the
system. Currently only has an effect on the networkd back-
end.
• use-mtu (bool)
Default: true. When true, the MTU received from the DHCP
server will be set as the MTU of the network interface.
When false, the MTU advertised by the DHCP server will be
ignored. Currently only has an effect on the networkd back-
end.
• hostname (scalar)
Use this value for the hostname which is sent to the DHCP
server, instead of machine's hostname. Currently only has
an effect on the networkd backend.
• use-routes (bool)
Default: true. When true, the routes received from the DHCP
server will be installed in the routing table normally.
When set to false, routes from the DHCP server will be ig-
nored: in this case, the user is responsible for adding
static routes if necessary for correct network operation.
This allows users to avoid installing a default gateway for
interfaces configured via DHCP. Available for both the net-
workd and NetworkManager backends.
• route-metric (scalar)
Use this value for default metric for automatically-added
routes. Use this to prioritize routes for devices by set-
ting a lower metric on a preferred interface. Available for
both the networkd and NetworkManager backends.
• use-domains (scalar) – since 0.98
Takes a boolean, or the special value "route". When true,
the domain name received from the DHCP server will be used
as DNS search domain over this link, similar to the effect
of the Domains= setting. If set to "route", the domain name
received from the DHCP server will be used for routing DNS
queries only, but not for searching, similar to the effect
of the Domains= setting when the argument is prefixed with
"~".
Requires feature: dhcp-use-domains
Routing
Complex routing is possible with netplan. Standard static routes as
well as policy routing using routing tables are supported via the net-
workd backend.
These options are available for all types of interfaces.
Default routes
The most common need for routing concerns the definition of default
routes to reach the wider Internet. Those default routes can only de-
fined once per IP family and routing table. A typical example would
look like the following:
network:
ethernets:
eth0:
[...]
routes:
- to: default # could be 0.0.0.0/0 optionally
via: 10.0.0.1
metric: 100
on-link: true
- to: default # could be ::/0 optionally
via: cf02:de:ad:be:ef::2
eth1:
[...]
routes:
- to: default
via: 172.134.67.1
metric: 100
on-link: true
# Not on the main routing table,
# does not conflict with the eth0 default route
table: 76
• routes (mapping)
The routes block defines standard static routes for an inter-
face. At least to must be specified. If type is local or nat
a default scope of host is assumed. If type is unicast and no
gateway (via) is given or type is broadcast, multicast or any-
cast a default scope of link is assumed. Otherwise, a global
scope is the default setting.
For from, to, and via, both IPv4 and IPv6 addresses are recog-
nized, and must be in the form addr/prefixlen or addr.
• from (scalar)
Set a source IP address for traffic going through the route.
(NetworkManager: as of v1.8.0)
• to (scalar)
Destination address for the route.
• via (scalar)
Address to the gateway to use for this route.
• on-link (bool)
When set to "true", specifies that the route is directly
connected to the interface. (NetworkManager: as of v1.12.0
for IPv4 and v1.18.0 for IPv6)
• metric (scalar)
The relative priority of the route. Must be a positive in-
teger value.
• type (scalar)
The type of route. Valid options are "unicast" (default),
"anycast", "blackhole", "broadcast", "local", "multicast",
"nat", "prohibit", "throw", "unreachable" or "xresolve".
• scope (scalar)
The route scope, how wide-ranging it is to the network.
Possible values are "global", "link", or "host". Applies to
IPv4 only.
• table (scalar)
The table number to use for the route. In some scenarios,
it may be useful to set routes in a separate routing table.
It may also be used to refer to routing policy rules which
also accept a table parameter. Allowed values are positive
integers starting from 1. Some values are already in use to
refer to specific routing tables: see /etc/iproute2/rt_ta-
bles. (NetworkManager: as of v1.10.0)
• mtu (scalar) – since 0.101
The MTU to be used for the route, in bytes. Must be a posi-
tive integer value.
• congestion-window (scalar) – since 0.102
The congestion window to be used for the route, represented
by number of segments. Must be a positive integer value.
• advertised-receive-window (scalar) – since 0.102
The receive window to be advertised for the route, repre-
sented by number of segments. Must be a positive integer
value.
• routing-policy (mapping)
The routing-policy block defines extra routing policy for a
network, where traffic may be handled specially based on the
source IP, firewall marking, etc.
For from, to, both IPv4 and IPv6 addresses are recognized, and
must be in the form addr/prefixlen or addr.
• from (scalar)
Set a source IP address to match traffic for this policy
rule.
• to (scalar)
Match on traffic going to the specified destination.
• table (scalar)
The table number to match for the route. In some scenarios,
it may be useful to set routes in a separate routing table.
It may also be used to refer to routes which also accept a
table parameter. Allowed values are positive integers
starting from 1. Some values are already in use to refer to
specific routing tables: see /etc/iproute2/rt_tables.
• priority (scalar)
Specify a priority for the routing policy rule, to influence
the order in which routing rules are processed. A higher
number means lower priority: rules are processed in order by
increasing priority number.
• mark (scalar)
Have this routing policy rule match on traffic that has been
marked by the iptables firewall with this value. Allowed
values are positive integers starting from 1.
• type-of-service (scalar)
Match this policy rule based on the type of service number
applied to the traffic.
Authentication
Netplan supports advanced authentication settings for ethernet and wifi
interfaces, as well as individual wifi networks, by means of the auth
block.
• auth (mapping)
Specifies authentication settings for a device of type ether-
nets:, or an access-points: entry on a wifis: device.
The auth block supports the following properties:
• key-management (scalar)
The supported key management modes are none (no key manage-
ment); psk (WPA with pre-shared key, common for home wifi);
eap (WPA with EAP, common for enterprise wifi); sae (used by
WPA3); and 802.1x (used primarily for wired Ethernet connec-
tions).
• password (scalar)
The password string for EAP, or the pre-shared key for WPA-
PSK.
The following properties can be used if key-management is eap or
802.1x:
• method (scalar)
The EAP method to use. The supported EAP methods are tls
(TLS), peap (Protected EAP), and ttls (Tunneled TLS).
• identity (scalar)
The identity to use for EAP.
• anonymous-identity (scalar)
The identity to pass over the unencrypted channel if the
chosen EAP method supports passing a different tunnelled
identity.
• ca-certificate (scalar)
Path to a file with one or more trusted certificate authori-
ty (CA) certificates.
• client-certificate (scalar)
Path to a file containing the certificate to be used by the
client during authentication.
• client-key (scalar)
Path to a file containing the private key corresponding to
client-certificate.
• client-key-password (scalar)
Password to use to decrypt the private key specified in
client-key if it is encrypted.
• phase2-auth (scalar) – since 0.99
Phase 2 authentication mechanism.
Properties for device type ethernets:
Status: Optional.
Purpose: Use the ethernets key to configure Ethernet interfaces.
Structure: The key consists of a mapping of Ethernet interface IDs.
Each ethernet has a number of configuration options. You don't need to
define each interface by their name inside the ethernets mapping. You
can use any ID that describes the interface and match the actual net-
work card using the match key. The general configuration structure for
Ethernets is shown below.
network:
ethernets:
device-id:
...
device-id is the interface identifier. If you use the interface name
as the ID, Netplan will match that interface.
Consider the example below. In this case, an interface called eth0
will be configured with DHCP.
network:
ethernets:
eth0:
dhcp4: true
The device-id can be any descriptive name your find meaningful. Al-
though, if it doesn't match a real interface name, you must use the
property match to identify the device you want to configure.
The example below defines an Ethernet connection called isp-interface
(supposedly an external interface connected to the Internet Service
Provider) and uses match to apply the configuration to the physical de-
vice with MAC address aa:bb:cc:00:11:22.
network:
ethernets:
isp-interface:
match:
macaddress: aa:bb:cc:00:11:22
dhcp4: true
Ethernet device definitions, beyond common ones described above, also
support some additional properties that can be used for SR-IOV devices.
• link (scalar) – since 0.99
(SR-IOV devices only) The link property declares the device as
a Virtual Function of the selected Physical Function device,
as identified by the given netplan id.
Example:
network:
ethernets:
enp1: {...}
enp1s16f1:
link: enp1
• virtual-function-count (scalar) – since 0.99
(SR-IOV devices only) In certain special cases VFs might need
to be configured outside of netplan. For such configurations
virtual-function-count can be optionally used to set an ex-
plicit number of Virtual Functions for the given Physical
Function. If unset, the default is to create only as many VFs
as are defined in the netplan configuration. This should be
used for special cases only.
Requires feature: sriov
• embedded-switch-mode (scalar) – since 0.104
(SR-IOV devices only) Change the operational mode of the em-
bedded switch of a supported SmartNIC PCI device (e.g. Mel-
lanox ConnectX-5). Possible values are switchdev or legacy,
if unspecified the vendor's default configuration is used.
Requires feature: eswitch-mode
• delay-virtual-functions-rebind (bool) – since 0.104
(SR-IOV devices only) Delay rebinding of SR-IOV virtual func-
tions to its driver after changing the embedded-switch-mode
setting to a later stage. Can be enabled when bonding/VF LAG
is in use. Defaults to false.
Requires feature: eswitch-mode
• infiniband-mode (scalar) – since 0.105
(InfiniBand devices only) Change the operational mode of a
IPoIB device. Possible values are datagram or connected. If
unspecified the kernel's default configuration is used.
Requires feature: infiniband
Properties for device type modems:
Status: Optional.
Purpose: Use the modems key to configure Modem interfaces. GSM/CDMA
modem configuration is only supported for the NetworkManager backend.
systemd-networkd does not support modems.
Structure: The key consists of a mapping of Modem IDs. Each modem has
a number of configuration options. The general configuration structure
for Modems is shown below.
network:
version: 2
renderer: NetworkManager
modems:
cdc-wdm1:
mtu: 1600
apn: ISP.CINGULAR
username: ISP@CINGULARGPRS.COM
password: CINGULAR1
number: "*99#"
network-id: 24005
device-id: da812de91eec16620b06cd0ca5cbc7ea25245222
pin: 2345
sim-id: 89148000000060671234
sim-operator-id: 310260
Requires feature: modems
• apn (scalar) – since 0.99
Set the carrier APN (Access Point Name). This can be omitted
if auto-config is enabled.
• auto-config (bool) – since 0.99
Specify whether to try and auto-configure the modem by doing a
lookup of the carrier against the Mobile Broadband Provider
database. This may not work for all carriers.
• device-id (scalar) – since 0.99
Specify the device ID (as given by the WWAN management ser-
vice) of the modem to match. This can be found using mmcli.
• network-id (scalar) – since 0.99
Specify the Network ID (GSM LAI format). If this is speci-
fied, the device will not roam networks.
• number (scalar) – since 0.99
The number to dial to establish the connection to the mobile
broadband network. (Deprecated for GSM)
• password (scalar) – since 0.99
Specify the password used to authenticate with the carrier
network. This can be omitted if auto-config is enabled.
• pin (scalar) – since 0.99
Specify the SIM PIN to allow it to operate if a PIN is set.
• sim-id (scalar) – since 0.99
Specify the SIM unique identifier (as given by the WWAN man-
agement service) which this connection applies to. If given,
the connection will apply to any device also allowed by de-
vice-id which contains a SIM card matching the given identifi-
er.
• sim-operator-id (scalar) – since 0.99
Specify the MCC/MNC string (such as "310260" or "21601") which
identifies the carrier that this connection should apply to.
If given, the connection will apply to any device also allowed
by device-id and sim-id which contains a SIM card provisioned
by the given operator.
• username (scalar) – since 0.99
Specify the username used to authenticate with the carrier
network. This can be omitted if auto-config is enabled.
Properties for device type wifis:
Status: Optional.
Purpose: Use the wifis key to configure WiFi access points.
Structure: The key consists of a mapping of WiFi IDs. Each wifi has a
number of configuration options. The general configuration structure
for WiFis is shown below.
network:
version: 2
wifis:
wlp0s1:
access-points:
"network_ssid_name":
password: "**********"
Note that systemd-networkd does not natively support wifi, so you need
wpasupplicant installed if you let the networkd renderer handle wifi.
• access-points (mapping)
This provides pre-configured connections to NetworkManager.
Note that users can of course select other access
points/SSIDs. The keys of the mapping are the SSIDs, and the
values are mappings with the following supported properties:
• password (scalar)
Enable WPA/WPA2 authentication and set the passphrase for
it. If neither this nor an auth block are given, the net-
work is assumed to be open. The setting
password: "S3kr1t"
is equivalent to
auth:
key-management: psk
password: "S3kr1t"
• mode (scalar)
Possible access point modes are infrastructure (the de-
fault), ap (create an access point to which other devices
can connect), and adhoc (peer to peer networks without a
central access point). ap is only supported with Network-
Manager.
• bssid (scalar) – since 0.99
If specified, directs the device to only associate with the
given access point.
• band (scalar) – since 0.99
Possible bands are 5GHz (for 5GHz 802.11a) and 2.4GHz (for
2.4GHz 802.11), do not restrict the 802.11 frequency band of
the network if unset (the default).
• channel (scalar) – since 0.99
Wireless channel to use for the Wi-Fi connection. Because
channel numbers overlap between bands, this property takes
effect only if the band property is also set.
• hidden (bool) – since 0.100
Set to true to change the SSID scan technique for connecting
to hidden WiFi networks. Note this may have slower perfor-
mance compared to false (the default) when connecting to
publicly broadcast SSIDs.
• wakeonwlan (sequence of scalars) – since 0.99
This enables WakeOnWLan on supported devices. Not all drivers
support all options. May be any combination of any, discon-
nect, magic_pkt, gtk_rekey_failure, eap_identity_req,
four_way_handshake, rfkill_release or tcp (NetworkManager on-
ly). Or the exclusive default flag (the default).
• regulatory-domain (scalar) – since 0.105
This can be used to define the radio's regulatory domain, to
make use of additional WiFi channels outside the "world do-
main". Takes an ISO / IEC 3166 country code (like GB) or 00
to reset to the "world domain". See wireless-regdb
(https://git.kernel.org/pub/scm/linux/kernel/git/sfor-
shee/wireless-regdb.git/tree/db.txt) for available values.
Requires dependency: iw, if it is to be used outside the net-
workd (wpa_supplicant) backend.
Properties for device type bridges:
Status: Optional.
Purpose: Use the bridges key to create Bridge interfaces.
Structure: The key consists of a mapping of Bridge interface names.
Each bridge has an optional list of interfaces that will be bridged to-
gether. The interfaces listed in the interfaces key (enp5s0 and enp5s1
below) must also be defined in your Netplan configuration. The general
configuration structure for Bridges is shown below.
network:
bridges:
br0:
interfaces:
- enp5s0
- enp5s1
dhcp4: true
...
When applied, a virtual interface of type bridge called br0 will be
created in the system.
The specific settings for bridges are defined below.
• interfaces (sequence of scalars)
All devices matching this ID list will be added to the bridge.
This may be an empty list, in which case the bridge will be
brought online with no member interfaces.
Example:
network:
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bridges:
br0:
interfaces: [switchports]
• parameters (mapping)
Customization parameters for special bridging options. Time
intervals may need to be expressed as a number of seconds or
milliseconds: the default value type is specified below. If
necessary, time intervals can be qualified using a time suffix
(such as "s" for seconds, "ms" for milliseconds) to allow for
more control over its behavior.
• ageing-time, aging-time (scalar)
Set the period of time to keep a MAC address in the forward-
ing database after a packet is received. This maps to the
AgeingTimeSec= property when the networkd renderer is used.
If no time suffix is specified, the value will be interpret-
ed as seconds.
• priority (scalar)
Set the priority value for the bridge. This value should be
a number between 0 and 65535. Lower values mean higher pri-
ority. The bridge with the higher priority will be elected
as the root bridge.
• port-priority (mapping)
Set the port priority per interface. The priority value is
a number between 0 and 63. This metric is used in the des-
ignated port and root port selection algorithms.
Example:
network:
ethernets:
eth0:
dhcp4: false
eth1:
dhcp4: false
bridges:
br0:
interfaces: [eth0, eth1]
parameters:
port-priority:
eth0: 10
eth1: 20
• forward-delay (scalar)
Specify the period of time the bridge will remain in Listen-
ing and Learning states before getting to the Forwarding
state. This field maps to the ForwardDelaySec= property for
the networkd renderer. If no time suffix is specified, the
value will be interpreted as seconds.
• hello-time (scalar)
Specify the interval between two hello packets being sent
out from the root and designated bridges. Hello packets
communicate information about the network topology. When
the networkd renderer is used, this maps to the Hel-
loTimeSec= property. If no time suffix is specified, the
value will be interpreted as seconds.
• max-age (scalar)
Set the maximum age of a hello packet. If the last hello
packet is older than that value, the bridge will attempt to
become the root bridge. This maps to the MaxAgeSec= proper-
ty when the networkd renderer is used. If no time suffix is
specified, the value will be interpreted as seconds.
• path-cost (mapping)
Set the per-interface cost of a path on the bridge. Faster
interfaces should have a lower cost. This allows a finer
control on the network topology so that the fastest paths
are available whenever possible.
Example:
network:
ethernets:
eth0:
dhcp4: false
eth1:
dhcp4: false
bridges:
br0:
interfaces: [eth0, eth1]
parameters:
path-cost:
eth0: 100
eth1: 200
• stp (bool)
Define whether the bridge should use Spanning Tree Protocol.
The default value is "true", which means that Spanning Tree
should be used.
Properties for device type bonds:
Status: Optional.
Purpose: Use the bonds key to create Bond (Link Aggregation) inter-
faces.
Structure: The key consists of a mapping of Bond interface names. Each
bond has an optional list of interfaces that will be part of the aggre-
gation. The interfaces listed in the interfaces key must also be de-
fined in your Netplan configuration. The general configuration struc-
ture for Bonds is shown below.
network:
bonds:
bond0:
interfaces:
- enp5s0
- enp5s1
- enp5s2
mode: active-backup
...
When applied, a virtual interface of type bond called bond0 will be
created in the system.
The specific settings for bonds are defined below.
• interfaces (sequence of scalars)
All devices matching this ID list will be added to the bond.
Example:
network:
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bonds:
bond0:
interfaces: [switchports]
• parameters (mapping)
Customization parameters for special bonding options. Time
intervals may need to be expressed as a number of seconds or
milliseconds: the default value type is specified below. If
necessary, time intervals can be qualified using a time suffix
(such as "s" for seconds, "ms" for milliseconds) to allow for
more control over its behavior.
• mode (scalar)
Set the bonding mode used for the interfaces. The default
is balance-rr (round robin). Possible values are balance-
rr, active-backup, balance-xor, broadcast, 802.3ad, balance-
tlb, and balance-alb. For Open vSwitch active-backup and
the additional modes balance-tcp and balance-slb are sup-
ported.
• lacp-rate (scalar)
Set the rate at which LACPDUs are transmitted. This is only
useful in 802.3ad mode. Possible values are slow (30 sec-
onds, default), and fast (every second).
• mii-monitor-interval (scalar)
Specifies the interval for MII monitoring (verifying if an
interface of the bond has carrier). The default is 0; which
disables MII monitoring. This is equivalent to the MIIMoni-
torSec= field for the networkd backend. If no time suffix
is specified, the value will be interpreted as milliseconds.
• min-links (scalar)
The minimum number of links up in a bond to consider the
bond interface to be up.
• transmit-hash-policy (scalar)
Specifies the transmit hash policy for the selection of
ports. This is only useful in balance-xor, 802.3ad and bal-
ance-tlb modes. Possible values are layer2, layer3+4, lay-
er2+3, encap2+3, and encap3+4.
• ad-select (scalar)
Set the aggregation selection mode. Possible values are
stable, bandwidth, and count. This option is only used in
802.3ad mode.
• all-members-active (bool) – since 0.106
If the bond should drop duplicate frames received on inac-
tive ports, set this option to false. If they should be de-
livered, set this option to true. The default value is
false, and is the desirable behavior in most situations.
Alias: all-slaves-active
• arp-interval (scalar)
Set the interval value for how frequently ARP link monitor-
ing should happen. The default value is 0, which disables
ARP monitoring. For the networkd backend, this maps to the
ARPIntervalSec= property. If no time suffix is specified,
the value will be interpreted as milliseconds.
• arp-ip-targets (sequence of scalars)
IPs of other hosts on the link which should be sent ARP re-
quests in order to validate that a port is up. This option
is only used when arp-interval is set to a value other than
0. At least one IP address must be given for ARP link moni-
toring to function. Only IPv4 addresses are supported. You
can specify up to 16 IP addresses. The default value is an
empty list.
• arp-validate (scalar)
Configure how ARP replies are to be validated when using ARP
link monitoring. Possible values are none, active, backup,
and all.
• arp-all-targets (scalar)
Specify whether to use any ARP IP target being up as suffi-
cient for a port to be considered up; or if all the targets
must be up. This is only used for active-backup mode when
arp-validate is enabled. Possible values are any and all.
• up-delay (scalar)
Specify the delay before enabling a link once the link is
physically up. The default value is 0. This maps to the
UpDelaySec= property for the networkd renderer. This option
is only valid for the miimon link monitor. If no time suf-
fix is specified, the value will be interpreted as millisec-
onds.
• down-delay (scalar)
Specify the delay before disabling a link once the link has
been lost. The default value is 0. This maps to the Down-
DelaySec= property for the networkd renderer. This option
is only valid for the miimon link monitor. If no time suf-
fix is specified, the value will be interpreted as millisec-
onds.
• fail-over-mac-policy (scalar)
Set whether to set all ports to the same MAC address when
adding them to the bond, or how else the system should han-
dle MAC addresses. The possible values are none, active,
and follow.
• gratuitous-arp (scalar)
Specify how many ARP packets to send after failover. Once a
link is up on a new port, a notification is sent and possi-
bly repeated if this value is set to a number greater than
1. The default value is 1 and valid values are between 1
and 255. This only affects active-backup mode.
For historical reasons, the misspelling gratuitious-arp is
also accepted and has the same function.
• packets-per-member (scalar) – since 0.106
In balance-rr mode, specifies the number of packets to
transmit on a port before switching to the next. When this
value is set to 0, ports are chosen at random. Allowable
values are between 0 and 65535. The default value is 1.
This setting is only used in balance-rr mode.
Alias: packets-per-slave
• primary-reselect-policy (scalar)
Set the reselection policy for the primary port. On failure
of the active port, the system will use this policy to de-
cide how the new active port will be chosen and how recovery
will be handled. The possible values are always, better,
and failure.
• resend-igmp (scalar)
In modes balance-rr, active-backup, balance-tlb and balance-
alb, a failover can switch IGMP traffic from one port to an-
other.
This parameter specifies how many IGMP membership reports
are issued on a failover event. Values range from 0 to 255.
0 disables sending membership reports. Otherwise, the first
membership report is sent on failover and subsequent reports
are sent at 200ms intervals.
• learn-packet-interval (scalar)
Specify the interval between sending learning packets to
each port. The value range is between 1 and 0x7fffffff.
The default value is 1. This option only affects balance-
tlb and balance-alb modes. Using the networkd renderer,
this field maps to the LearnPacketIntervalSec= property. If
no time suffix is specified, the value will be interpreted
as seconds.
• primary (scalar)
Specify a device to be used as a primary port, or preferred
device to use as a port for the bond (i.e. the preferred
device to send data through), whenever it is available.
This only affects active-backup, balance-alb, and balance-
tlb modes.
Properties for device type tunnels:
Status: Optional.
Purpose: Use the tunnels key to create virtual tunnel interfaces.
Structure: The key consists of a mapping of tunnel interface names.
Each tunnel requires the identification of the tunnel mode (see the
section mode below for the list of supported modes). The general con-
figuration structure for Tunnels is shown below.
network:
tunnels:
tunnel0:
mode: SCALAR
...
When applied, a virtual interface called tunnel0 will be created in the
system. Its operation mode is defined by the property mode.
Tunnels allow traffic to pass as if it was between systems on the same
local network, although systems may be far from each other but reach-
able via the Internet. They may be used to support IPv6 traffic on a
network where the ISP does not provide the service, or to extend and
"connect" separate local networks. Please see
<https://en.wikipedia.org/wiki/Tunneling_protocol> for more general in-
formation about tunnels.
The specific settings for tunnels are defined below.
• mode (scalar)
Defines the tunnel mode. Valid options are sit, gre, ip6gre,
ipip, ipip6, ip6ip6, vti, vti6, wireguard, vxlan, gretap and
ip6gretap modes. In addition, the NetworkManager backend sup-
ports isatap tunnels.
• local (scalar)
Defines the address of the local endpoint of the tunnel. (For
VXLAN) This should match one of the parent's IP addresses or
make use of the networkd special values.
• remote (scalar)
Defines the address of the remote endpoint of the tunnel or
multicast group IP address for VXLAN.
• ttl (scalar) – since 0.103
Defines the Time To Live (TTL) of the tunnel. Takes a number
in the range 1..255.
• key (scalar or mapping)
Define keys to use for the tunnel. The key can be a number or
a dotted quad (an IPv4 address). For wireguard it can be a
base64-encoded private key or (as of networkd v242+) an abso-
lute path to a file, containing the private key (since 0.100).
It is used for identification of IP transforms. This is only
required for vti and vti6 when using the networkd backend.
This field may be used as a scalar (meaning that a single key
is specified and to be used for input, output and private
key), or as a mapping, where you can further specify in-
put/output/private.
• input (scalar)
The input key for the tunnel
• output (scalar)
The output key for the tunnel
• private (scalar) – since 0.100
A base64-encoded private key required for WireGuard tunnels.
When the systemd-networkd backend (v242+) is used, this can
also be an absolute path to a file containing the private
key.
• keys (scalar or mapping)
Alternate name for the key field. See above.
Examples:
network:
tunnels:
tun0:
mode: gre
local: ...
remote: ...
keys:
input: 1234
output: 5678
network:
tunnels:
tun0:
mode: vti6
local: ...
remote: ...
key: 59568549
network:
tunnels:
wg0:
mode: wireguard
addresses: [...]
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
shared: /path/to/shared.key
...
key: mNb7OIIXTdgW4khM7OFlzJ+UPs7lmcWHV7xjPgakMkQ=
network:
tunnels:
wg0:
mode: wireguard
addresses: [...]
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
...
keys:
private: /path/to/priv.key
WireGuard specific keys:
• mark (scalar) – since 0.100
Firewall mark for outgoing WireGuard packets from this inter-
face, optional.
• port (scalar) – since 0.100
UDP port to listen at or auto. Optional, defaults to auto.
• peers (sequence of mappings) – since 0.100
A list of peers, each having keys documented below.
Example:
network:
tunnels:
wg0:
mode: wireguard
key: /path/to/private.key
mark: 42
port: 5182
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
allowed-ips: [0.0.0.0/0, "2001:fe:ad:de:ad:be:ef:1/24"]
keepalive: 23
endpoint: 1.2.3.4:5
- keys:
public: M9nt4YujIOmNrRmpIRTmYSfMdrpvE7u6WkG8FY8WjG4=
shared: /some/shared.key
allowed-ips: [10.10.10.20/24]
keepalive: 22
endpoint: 5.4.3.2:1
• endpoint (scalar) – since 0.100
Remote endpoint IPv4/IPv6 address or a hostname, followed by
a colon and a port number.
• allowed-ips (sequence of scalars) – since 0.100
A list of IP (v4 or v6) addresses with CIDR masks from which
this peer is allowed to send incoming traffic and to which
outgoing traffic for this peer is directed. The catch-all
0.0.0.0/0 may be specified for matching all IPv4 addresses,
and ::/0 may be specified for matching all IPv6 addresses.
• keepalive (scalar) – since 0.100
An interval in seconds, between 1 and 65535 inclusive, of
how often to send an authenticated empty packet to the peer
for the purpose of keeping a stateful firewall or NAT map-
ping valid persistently. Optional.
• keys (mapping) – since 0.100
Define keys to use for the WireGuard peers.
This field can be used as a mapping, where you can further
specify the public and shared keys.
• public (scalar) – since 0.100
A base64-encoded public key, required for WireGuard peers.
• shared (scalar) – since 0.100
A base64-encoded preshared key. Optional for WireGuard
peers. When the systemd-networkd backend (v242+) is used,
this can also be an absolute path to a file containing the
preshared key.
VXLAN specific keys:
• id (scalar) – since 0.105
The VXLAN Network Identifier (VNI or VXLAN Segment ID). Takes
a number in the range 1..16777215.
• link (scalar) – since 0.105
netplan ID of the parent device definition to which this VXLAN
gets connected.
• type-of-service (scalar) – since 0.105
The Type Of Service byte value for a vxlan interface.
• mac-learning (scalar) – since 0.105
Takes a boolean. When true, enables dynamic MAC learning to
discover remote MAC addresses.
• ageing, aging (scalar) – since 0.105
The lifetime of Forwarding Database entry learned by the ker-
nel, in seconds.
• limit (scalar) – since 0.105
Configures maximum number of FDB entries.
• arp-proxy (scalar) – since 0.105
Takes a boolean. When true, bridge-connected VXLAN tunnel
endpoint answers ARP requests from the local bridge on behalf
of remote Distributed Overlay Virtual Ethernet (DOVE) clients.
Defaults to false.
• notifications (sequence of scalars) – since 0.105
Takes the flags l2-miss and l3-miss to enable netlink LLADDR
and/or netlink IP address miss notifications.
• short-circuit (scalar) – since 0.105
Takes a boolean. When true, route short circuiting is turned
on.
• checksums (sequence of scalars) – since 0.105
Takes the flags udp, zero-udp6-tx, zero-udp6-rx, remote-tx and
remote-rx to enable transmitting UDP checksums in VXLAN/IPv4,
send/receive zero checksums in VXLAN/IPv6 and enable send-
ing/receiving checksum offloading in VXLAN.
• extensions (sequence of scalars) – since 0.105
Takes the flags group-policy and generic-protocol to enable
the "Group Policy" and/or "Generic Protocol" VXLAN extensions.
• port (scalar) – since 0.105
Configures the default destination UDP port. If the destina-
tion port is not specified then Linux kernel default will be
used. Set to 4789 to get the IANA assigned value.
• port-range (sequence of scalars) – since 0.105
Configures the source port range for the VXLAN. The kernel
assigns the source UDP port based on the flow to help the re-
ceiver to do load balancing. When this option is not set, the
normal range of local UDP ports is used. Uses the form [LOW-
ER, UPPER].
• flow-label (scalar) – since 0.105
Specifies the flow label to use in outgoing packets. The
valid range is 0-1048575.
• do-not-fragment (scalar) – since 0.105
Allows setting the IPv4 Do not Fragment (DF) bit in outgoing
packets. Takes a boolean value. When unset, the kernel's de-
fault will be used.
Properties for device type vlans:
Status: Optional.
Purpose: Use the vlans key to create VLAN interfaces.
Structure: The key consists of a mapping of VLAN interface names. The
interface used in the link option (enp5s0 in the example below) must
also be defined in the Netplan configuration. The general configura-
tion structure for Vlans is shown below.
network:
vlans:
vlan123:
id: 123
link: enp5s0
dhcp4: yes
The specific settings for VLANs are defined below.
• id (scalar)
VLAN ID, a number between 0 and 4094.
• link (scalar)
netplan ID of the underlying device definition on which this
VLAN gets created.
Example:
network:
ethernets:
eno1: {...}
vlans:
en-intra:
id: 1
link: eno1
dhcp4: yes
en-vpn:
id: 2
link: eno1
addresses: [...]
Properties for device type vrfs:
Status: Optional.
Purpose: Use the vrfs key to create Virtual Routing and Forwarding
(VRF) interfaces.
Structure: The key consists of a mapping of VRF interface names. The
interface used in the link option (enp5s0 in the example below) must
also be defined in the Netplan configuration. The general configura-
tion structure for VRFs is shown below.
network:
renderer: networkd
vrfs:
vrf1:
table: 1
interfaces:
- enp5s0
routes:
- to: default
via: 10.10.10.4
routing-policy:
- from: 10.10.10.42
• table (scalar) – since 0.105
The numeric routing table identifier. This setting is compul-
sory.
• interfaces (sequence of scalars) – since 0.105
All devices matching this ID list will be added to the VRF.
This may be an empty list, in which case the VRF will be
brought online with no member interfaces.
• routes (sequence of mappings) – since 0.105
Configure static routing for the device; see the Routing sec-
tion. The table value is implicitly set to the VRF's table.
• routing-policy (sequence of mappings) – since 0.105
Configure policy routing for the device; see the Routing sec-
tion. The table value is implicitly set to the VRF's table.
Example:
network:
vrfs:
vrf20:
table: 20
interfaces: [ br0 ]
routes:
- to: default
via: 10.10.10.3
routing-policy:
- from: 10.10.10.42
[...]
bridges:
br0:
interfaces: []
Properties for device type nm-devices:
Status: Optional. Its use is not recommended.
Purpose: Use the nm-devices key to configure device types that are not
supported by Netplan. This is NetworkManager specific configuration.
Structure: The key consists of a mapping of NetworkManager connections.
The nm-devices device type is for internal use only and should not be
used in normal configuration files. It enables a fallback mode for un-
supported settings, using the passthrough mapping. The general config-
uration structure for NM connections is shown below.
network:
version: 2
nm-devices:
NM-db5f0f67-1f4c-4d59-8ab8-3d278389cf87:
renderer: NetworkManager
networkmanager:
uuid: "db5f0f67-1f4c-4d59-8ab8-3d278389cf87"
name: "myvpnconnection"
passthrough:
connection.type: "vpn"
vpn.ca: "path to ca.crt"
vpn.cert: "path to client.crt"
vpn.cipher: "AES-256-GCM"
vpn.connection-type: "tls"
vpn.dev: "tun"
vpn.key: "path to client.key"
vpn.remote: "1.2.3.4:1194"
vpn.service-type: "org.freedesktop.NetworkManager.openvpn"
Backend-specific configuration parameters
In addition to the other fields available to configure interfaces, some
backends may require to record some of their own parameters in netplan,
especially if the netplan definitions are generated automatically by
the consumer of that backend. Currently, this is only used with Net-
workManager.
• networkmanager (mapping) – since 0.99
Keeps the NetworkManager-specific configuration parameters
used by the daemon to recognize connections.
• name (scalar) – since 0.99
Set the display name for the connection.
• uuid (scalar) – since 0.99
Defines the UUID (unique identifier) for this connection, as
generated by NetworkManager itself.
• stable-id (scalar) – since 0.99
Defines the stable ID (a different form of a connection
name) used by NetworkManager in case the name of the connec-
tion might otherwise change, such as when sharing connec-
tions between users.
• device (scalar) – since 0.99
Defines the interface name for which this connection ap-
plies.
• passthrough (mapping) – since 0.102
Can be used as a fallback mechanism to missing keyfile set-
tings.
SEE ALSO
netplan-generate(8), netplan-apply(8), netplan-try(8), netplan-get(8),
netplan-set(8), netplan-info(8), netplan-ip(8), netplan-rebind(8), net-
plan-status(8), netplan-dbus(8), systemd-networkd(8), NetworkManager(8)
AUTHORS
Mathieu Trudel-Lapierre (<cyphermox@ubuntu.com>); Martin Pitt (<mar-
tin.pitt@ubuntu.com>); Lukas Märdian (<slyon@ubuntu.com>).
YAML configuration(5)
Generated by dwww version 1.14 on Mon Feb 24 15:36:17 CET 2025.